EarthQuake MiniMe P10 User Manual download pdf (Page 5)

(1) Line Level RCA Inputs terminals will accept up to 16-gauge quality speaker

Connect with RCA type patch cords to the line level wire. The Inputs should be connected to the left and

output of your receiver or pre-amp. If your pre- right speaker terminals of your amplifier or receiver.

amplifier or receiver has a single sub/LFE output, The Outputs should run from the subwoofer to the left

connect it to the subwoofer's left input jack. There is and right satellite speakers. Remember: Always

no need to use the subwoofers right input jack. If you connect red-to-red and black-to-black, when making

want to run your main/satellite speakers full range, connections between an amplifier/receiver to the

use a "Y" adapter at the pre-amplifier outputs. In this subwoofer. If you inadvertently reverse one of the

way, you can send the pre-amplifier's output signal to connections (i.e., red-to-black), you will notice a lack

your main amplifier and to the subwoofer at the same of bass from your subwoofer.

time.

(3) Voltage Selection Switch

(2) High Level Inputs / Outputs

Under normal conditions, the preferred connection is

through the Line Level inputs. If this is difficult or not

possible in your system, then you can use the

Speaker Level inputs. Also, if you experience

excessive noise or hum with the Line Level input,

often a simple change to the Speaker Level input will

result in a lower background noise level.

(4) Manual ON/OFF Switch

Connect the Speaker Level inputs to the speaker-level In the “ON” position, the subwoofer will remain “on”

outputs of your amplifier or receiver using speaker constantly or can turn “on” and “off” automatically

wire. The binding posts can accept bare wire when the “AUTO/ON” circuit is engaged. In the “OFF”

connections only. position, the subwoofer will remain off until the switch

is manually turned back to the “ON” position.

High Level: Connecting the Subwoofer using the high

level speaker connections: On the rear of your MiniMe (5) Line Fuse

Subwoofer are two pairs of red and black binding The subwoofer is supplied with a conservative, slow-

posts. One set is marked “Input” and one set is blow type fuse to protect the electronics.

marked “Output”, with each pair designated as left or

right. Each post is color-coded black/red. These

The voltage switch is positioned according to area

voltage requirements. It has been pre-set

prior to shipping from the factory.

CAUTION

Do not try to alter the voltage setting, as doing so will

result in a blown fuse. A wrong setting

may result in damaged electronics.

Control Panel Overview

Overview Continued On Next Page»

(5) Line Fuse

(9) 0-180° Phase Shift

(11) 50Hz - 160Hz

Frequency Adjustment

(12) Volume Control

(10) Sub Operation Switch

(8) Power Status LED

(1)

Inputs and Outputs

Line Level RCA

(7) Auto ON/OFF

(2) Speaker

Inputs and Outputs

Level

(4) Manual ON/OFF Switch(3) Voltage Selection Switch

(6) 110-120V AC Power Connection

Earthquake • MiniMe User Manual

Earthquake Sound, 2727 McCone Avenue, Hayward, CA 94545 USA

www.earthquakesound.com

VOLUME

FREQUENCY

MODE

PHASE

AUTO

MIN

50Hz

MAX

RIGHT

POWER

LEFT

160Hz

SUB

OFF

LFE

180

110-120VAC~60Hz

220-240VAX~50Hz

FUSE: 115V, T6.4AL/250V

FUSE: 230V, T3.2AL/250V

110-120V

220-240V

OFF

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING

WARNING: SHOCK HAZARD-DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

P O W E R

DIGITAL

600 WATTS

POWERED

SUBWOOFER

FUSE

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comments to this Manuals

No comments

EarthQuake MiniMe P10 User Manual Page 5

Comments to this Manuals

Related products and manuals for Subwoofers EarthQuake MiniMe P10